Stirrer Accessories
CARLISLE SANITARY MAINTENANCE PRODUCTS REPL BLADE 4-1/2INX7-1/2IN 6CS
NC1456180 REPL BLADE 4-1/2INX7-1/2IN 6CS
Chemglass Life Sciences Rushton Style Impeller Blade for 2-3L Bio Reactors, 46mm Dia for 8mm OD Shaft
This adapter can be used to add fluids or gases to the bio reactor.The portion of the adapter that is within the reactor has a short drip tip tube that can accept tubing to reach further into the listed capacity reactor.Stainless steel components manufactured from 316L with an electropolished surface finish of 20Ra or better.Like-for-like replacement parts for Applikon Biotechnology and Broadley-James brands of bioreactors.Applikon is a registered trademark of Applikon Biotechnology, Inc.Broadley-James and Broadley-James Corporation are registered trademarks of Broadley-James Corporation.
McMaster-Carr Clamping Two-Piece Shaft Collar
Clamping Two-Piece Shaft Collarfor 20 mm Diameter, 2024 Aluminum
Chemglass Life Sciences Stirrer Bearing, Macro, Jacketed, Glass, for 10mm Shaft, 29/42 Inner Joint
Stirrer Bearing,Macro, Jacketed, Glass, for 10mm Shaft, 29/42 Inner Joint. Similar to CG-2070, but water jacketed to control bearing temperature. For use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
Chemglass Life Sciences Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 525mm OAL, Agitator OD 66mm, for use with 1, 000mL Reactors
Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 525mm OAL, Agitator OD 66mm, for use with 1,000mL Reactors. Shaft is precision ground and polished to fit Chemglass's CG-2077-H, CG-2077-G and CG-2077-U style 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120 apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR CLOCKWISE ROTATION.
Chemglass Life Sciences Attachment Plug, Serrated, PTFE
Attachment Plug, Serrated, PTFE. Component of CG-2095 series of agitators. THIS ITEM IS ATTACHMENT PLUG ONLY!
Chemglass Life Sciences Nylon Chuck for 6mm to 1/4" Stir Shaft
Nylon Chuck for 6mm to 1/4" Stir Shaft. For use with the CG-2039-A-500 Micro Overhead Stirrer for Tissue Grinder. Pictured is the micro overhead stirrer.
Chemglass Life Sciences 6.35mm Tru-Stir Stirrer Shaft Coupling, 3/8" Upper Male Coupling, For Use with 3-Jaw Jacobs Chuck
6.35mm Tru-Stir Stirrer Shaft Coupling, 3/8" Upper Male Coupling, For Use with 3-Jaw Jacobs Chuck. The unique design of Chemglass's Tru-Stir stirrer shaft coupling eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors. Coupling incorporates a unique helical Stainless Steel spring permitting up to 1/4 of offset misalignment and 45 of angular misalignment. Coupling is rated for 24 in-lbs of torque without the backlash normally associated with common coil springs. Lower portion of coupling has a nylon adapter with a one piece collar for attachment to 10, 19, 25.4 and 30mm stir shafts. Upper adapters permit the coupling to be used with a standard Jacobs style 3-jaw chuck or motors having shaft diameters of 5/16, 3/8, 12mm, 1/2, 5/8 or 3/4. Adapter is also available for use with CG-2047 flexible shafts having 5/16 end fittings. Overall length of the coupling is 4. Supplied complete with an allen wrench set.
Chemglass Life Sciences 30mm Stirrer Shaft Coupling, Universal, 3/8" OD Stud
30mm Stirrer Shaft Coupling, Universal, 3/8" OD Stud. Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Stainless Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench.
Chemglass Life Sciences 19mm Rotary Bearing Taper Lock, Ferrule, Nylon
19mm Rotary Bearing Taper Lock, Ferrule, Nylon. Component of CG-2077-M series of mechanical seal stir bearings. Pictured is a fully assembled bearing. Item is ROTARY BEARING TAPER LOCK FERRULE ONLY.
Chemglass Life Sciences 13" One-Piece PTFE Lower Agitator, Four Blade, For Use with 30mm Shafts, For use with 400mm ID Flange Reactor
13" One-Piece PTFE Lower Agitator, Four Blade, For Use with 30mm Shafts, For use with 400mm ID Flange Reactor. High viscosity agitator. The body is made entirely from ONE PIECE of CLASS VI VIRGIN PTFE. One-piece machined body is much easier to clean. The smooth machined surface has no seams, joints or crevices for material to collect. The design provides excellent stirring at the bottom of CG-1968-W 400mm ID 100L reactor vessels, especially when heavy slurries are being mixed. Agitator attaches to stir shaft by both a compression fitting and a PTFE safety pin. Heavy duty blades 9mm thick. For use with 30mm CG-2097 stirrer shafts. PLEASE NOTE: THE LOWER AGITATOR HAS BUSHING TO ACCEPT A STABILIZING PIN FROM DRAIN VALVE PLUG. THE PIN EXTENDS INTO THE LOWER AGITATOR AND VIRTUALLY ELIMINATES ANY WHIPPING BY STABILIZING THE STIRRER SHAFT.